This section describes the steps that players must perform before playing a game of BOW.

Before playing their first battle, players should insert the figures into the figure bases provided, making sure that the hole for the banner pole is at the rear of the unit (see "Assembling Figures” sidebar on page 7).

Setting Up

To prepare the play area, follow the instructions in this section.

First-time players should play the “Clash on the Kingsroad” battle first. Players can open the Westeros Battle Plans to page 4 for reference. A diagram of the component setup (without figures) of “Clash on the Kingsroad” can be found below.

1. Choose a Battle and a House to Play

Players must first choose a battle to play. Battles can be found in the Westeros Battle Plans (in this box), online at www.FantasyFlightGames.com , and in future expansion sets for BOW. After choosing a battle, players decide which House each player will control for the battle. In the BOW core game, players have the choice of controlling either House Stark (white) or House Lannister (red). If both players wish to control the same House, players determine randomly (such as by flipping a coin) who controls which House.

Players take the command board, the Leadership cards, the Commander cards, and the Unit Reference cards of their chosen House. Each card for a particular House has the House’s symbol on the back or in the upper left in the case of the Commander cards (depicted in the “House Symbols” sidebar above).

2. Create the Battlefield

Following the battle plan, players unfold the map board and place it in the center of the table with the side indicated by the battle plan faceup (there is only one map board in the core game, but the maps on each side are different).

This map board serves as the battlefield. Players then place any additional map overlays and/or special tokens required by the battle onto the battlefield. For more information on setting up the battlefield, please refer to the included Westeros Battle Plans.

Each player sits with his House’s board edge (as shown by the colored border and matching House symbol on the battlefield map in the battle plan) directly in front of him.

3. Take Commanders

Each battle requires specific commanders. The battle plan shows which commanders each player takes and what hex each commander (and his unit) starts in.

After determining which of his commanders are used in the battle, each player takes the corresponding commander figures and Commander cards and places them in his play area (the area between himself and the battlefield). Return unused commander figures and Commander cards to the box.

It is important to note that some commanders have multiple Commander cards. Refer to the commander’s title below the commander’s name to make sure the card is taken. The battle plan notes which version must be used.

For example, Greatjon Umber has two different versions: “The Greatjon” and “Lord of Last Hearth.” 

Commander cards should be placed uncommitted side up so that the full color portrait of the commander is faceup in the play area.

4. Build Leadership Decks

Each House has 10 Leadership cards with no commander’s picture in the lower right hand corner. These 10 cards are the House’s basic Leadership cards. Each player sets his House’s basic Leadership cards aside.

Each commander has five Leadership cards with his picture in the lower right corner. These five cards are the commander-specific cards for that commander. Each player takes all of the commanderspecific cards that match his commanders (who were taken in step 3) and shuffles them thoroughly with the 10 basic Leadership cards for his House. He then places this deck facedown in his play area to form his House’s Leadership deck.

Leadership cards come in two varieties: basic and commanderspecific.

Command Box - A command box has a Command icon in the upper left corner of the text box.
Tactic Box - A tactic box does not have a Command icon in the upper left corner of the text box.

5. Place Round Track and Round Marker

Place the round track to one side of the battlefield with the round marker on the “1” space. The number on the battle plan next to the Round Limit icon (see icon to the left) shows how many rounds a battle lasts.

6. Place Morale Track and Morale Marker

Players assemble the morale track and place it next to the battlefield.

The morale track has three pieces. The morale hub goes in the center, with the two House morale segments projecting from it on opposite sides. To create the morale track, each player attaches his House’s morale segment to the hub to form a line (see “Clash on the Kingsroad” Component Setup diagram on page 6). The two segments and the hub, when connected, form the morale track.
After the morale track has been placed next to the battlefield, each player’s House morale segment must be the one nearest to his board edge.

Make sure that the side of their morale segment that is faceup corresponds to the side indicated in the battle plan. The last space of each morale segment must match the space dictated in the battle plan.

In the core game, the only difference between the sides of a morale segment is that one side has an “11” space as its last space while the other side has a Rout space.

After forming the morale track, players place the morale marker on the morale starting space (the center space of the morale hub).

7. Create Token Stockpiles and Place Command Tokens

Players now sort the tokens for use during the game into piles. 
These tokens should be placed within easy reach of both players to form the stockpiles for the game.

The most commonly used tokens include order tokens, command tokens, and engagement tokens. Some battles also require other tokens, such as strategy tokens.

Each player takes a number of command tokens equal to the number beside the Command icon in the battle plan and places them on his command board.

8. Form and Place Units

Players now consult the battlefield map in the battle plan to see what starting units they will use for the battle and where those units will be deployed. Each unit is an individual fighting group that occupies a single hex. A unit consists of a certain number of figures (normally three or four depending on the figure’s bases).

A unit on the battlefield map is represented by a single silhouette of one of its figures (see the “Forming Units” sidebar on page 10). 
In the core game, figures come in one of three different classes: infantry, ranged, or cavalry. The banner color behind this figure on the map shows the rank of the unit that corresponds to the color of its banner (green, blue, or red).

Prior to placing any units on the board, players lay out the banners for the current battle. The punchboard banner must be securely inserted into a banner pole before placing a banner in its corresponding hex (see sidebar).
After all of the banners have been laid out, players form units for each hex containing a friendly banner as described under “Forming Units” on the next page.
After a unit has been formed, it is then placed in its corresponding hex as shown on the battlefield map. The banner in that hex is then placed in the banner hole of one of the figures. If a commander is in a unit, the banner must go into his base.
A unit with a commander shows the commander’s figure with a banner representing the rank of the unit. The battle plan shows a picture of what commander should be used. Different versions of the same commander are identified by their titles.
The owning player refers to the upper left corner of the
Commander card’s uncommitted side (the full-color side) to see what kind of unit must be placed with this commander figure.
Form the unit as normal except the commander figure takes the place of one of the normal figures (as the banner bearer). See the “Forming Units” sidebar on page 10 for more details.

9. Assign the Momentum Token

The battle plan specifies which House possesses the momentum token. That player places the momentum token in his play area.

Players are now ready to begin the battle!

Log in to comment